![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
* sw:1 # configure iproute add ip-addr netmask next-hop metric
* sw:1 # enable ipforwarding
sw:1 # create vlan vlan-name
sw:2 # configure vlan-name ipaddress ip-addr netmask IP interface for VLAN vlan-name has been created. IP address = ip-addr, Netmask = netmask.
sw:3 # configure default delete port port-num
sw:4 # configure vlan-name add port port-num
* sw:1 # show vlan
Name VID Protocol Addr Flags Proto Ports
Default 1 0.0.0.0 /BP -----T-------- ANY 0/16
MacVlanDiscover 4095 ------------------ -------- ANY 0/0
Mgmt 4094 ------------------ -------- ANY 0/1
vlan1 4093 ------------------ -------- ANY 0/8
vlan2 4092 ------------------ -------- ANY 0/8
Flags: (C) Domain-masterVlan, (c) Domain-memberVlan, (d) DVMRP Enabled
(E) ESRP Slave, (f) IP Forwarding Enabled, (G) GVRP Enabled
(i) ISIS Enabled, (I) IP Forwarding lpm-routing Enabled
(L) Loopback Enabled, (M) ESRP Master, (m) IPmc Forwarding Enabled
(N) GNS Reply Enabled, (o) OSPF Enabled, (p) PIM Enabled
(R) SubVLAN IP Range Configured, (r) RIP Enabled, (S) SuperVlan
(s) SubVlan, (T) Member of STP Domain, (v) VRRP Enabled
(V) VPLS/TLS Enabled, (X) IPX RIP Enabled, (Z) Translation-Vlan
(z) Member-Vlan, (2) IPX Type 20 Forwarding Enabled
/BP: Waiting for bootp reply.
Total number of Vlan(s) : 5
* sw:1 # show configuration
* sw:1 # save configuration Do you want to save to the primary configuration database? yes >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>!. Verifying the configuration... Done! Saved to primary configuration database. sw:2 #
sw:1 # configure snmp sysname hostname
sw:1 # configure account admin password: Reenter password:
sw:1 # configure account user password: Reenter password:
sw:1 # show accounts
User Name Access LoginOK Failed User Type
---------------- ------ ------- ------ ---------
admin R/W 1 0 Admin
user RO 0 0 User
--------------------------------------------------
(*) - Account locked
sw:1 # reboot Are you sure you want to reboot the switch (y/n)? y
#pre(soft){{
Boot Module 4 SEP 03 v8.2
==========================
Memory Size: 10000000
Press spacebar for boot menu
BootROM-> ?
1: Select primary code image
2: Select secondary code image
3: Select primary configuration
4: Select secondary configuration
b: Change baud rate
d: Force default configuration
f: Boot on board flash
h: Help
k: Erase selected configuration
p: Boot PCMCIA card
s: Load code image from serial port using XMODEM
BootROM-> d
BootROM-> f
Uncompressing primary image from flash........................................
................................................................................
................................................................................
......................!
ExtremeWare
Copyright (C) 1996-2005 Extreme Networks. All rights reserved.
Protected by U.S Patent Nos 6,678,248; 6,104,700; 6,766,482; 6,618,388; 6,034,95
7; 6,859,438; 6,912,592; 6,914,905
================================================================================
Version 7.5.3.8 [non-ssh] [base] by Release_Master on MM/DD/YY hh:mm:ss
System Serial Number: XXXXXXXXX
Memory Size: 268435456 (256MB)
login: admin
password:
ExtremeWare
Copyright (C) 1996-2005 Extreme Networks. All rights reserved.
Protected by U.S Patent Nos 6,678,248; 6,104,700; 6,766,482; 6,618,388; 6,034,95
7; 6,859,438; 6,912,592; 6,914,905
================================================================================
Press the <tab> key at any time for completions.
Remember to save your configuration changes.
* Summit7iTx:1 #
